Oce Arizona 318 GL Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 224

background image

Roll Media Option Specifications

Introduction

The Roll Media Option available for the Océ Arizona 318 GLprinters allows the use of various
flexible media that are supplied on a roll. Specifications associated with the use of roll media are
indicated in this section.

NOTE

The Océ Arizona 318 GL and the Roll Media Option must be operated in accordance with the

environmental conditions specified in the Océ Arizona 318 GL Site Preparation Guide and all

safety requirements noted in this document.

Media Size Supported

Width (Max.): 2.2m (86.6")

Width (Min.): 0.9m (36")

Roll Diameter (Max.): 240mm (9.45”)

Core Inner Diameter: 76.2mm (3”)

Print Size Supported

2.190m (86.2”)

This allows for a minimum 5mm (0.2”) border. This is necessary to ensure the platen is not
contaminated with ink due to possible media tracking errors. Cured and uncured ink on the platen
will have a serious effect on printer performance. Any spilled ink must be removed immediately
(See RMO Maintenance section). If an image exceeds the 5mm border requirement, printing will
not be allowed to proceed.

Maximum Media Thickness

This value is not officially specified. It is theoretically possible for the RMO system to
accommodate media up to 3mm (0.11 inches). However, most media at or near that thickness will
have problems in the transport mechanism of the RMO unit.

Maximum Supported Weight

Media Width (mm)

Max. Weight kg (lbs)

900 ≤ x < 1220

28 (62)

1220 ≤ x < 1480

40 (88)

1480 ≤ x < 1780

45 (100)

1780 ≤ x ≤ 2200

50 (110)

Leader & End of Roll Waste

Leader Waste

: 560mm (22 inches)

Leader waste is the amount of media that cannot be printed between the roll media platen and
the take-up media roll. This waste is produced every time media is loaded, taped to the take-up
core and initialized in preparation for the first print. Trailer waste is the media that cannot be

Roll Media Option Specifications

78

Chapter 6 - How to Operate the Roll Media Option

«
...
76
77
78
79
80
...
»

Содержание Arizona 318 GL

































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Arizona 318 GL

Бренд: LabelTac Страницы: 2

Бренд: Xerox Страницы: 341

Бренд: Panasonic Страницы: 2

Бренд: Xerox Страницы: 414

WorkCentre 4265

Бренд: Xerox Страницы: 20

Бренд: Xerox Страницы: 11

Бренд: Oki Страницы: 4

Бренд: A&D Страницы: 24

Бренд: Ricoh Страницы: 2

Бренд: DPM Страницы: 2

Бренд: PolyPrinter Страницы: 36

Бренд: Printekmobile Страницы: 2

Бренд: SEWOO Страницы: 8

Бренд: FujiFilm Страницы: 28

Бренд: Triumph Adler Страницы: 202

Бренд: Oki Страницы: 174

Бренд: Wasp Страницы: 73

Бренд: Kyocera Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды