Oce Arizona 318 GL Скачать руководство пользователя страница 175 | Manualshive

Страница: 175 / 224

background image

Printhead Maintenance

Introduction

The Maintenance Station is located below the carriage. When you perform printhead
maintenance, any excess ink and associated debris are removed from the nozzles with the result
that ink drops can jet properly when the nozzles are clear.

NOTE

The nozzle plate on the printhead has a non-wetting coating - contact with this surface may

affect the performance of the printhead. Do not wipe the nozzle plate with anything other than

the suction-head (or the supplied swabs when following the swab procedure) as this can

damage the nozzles and impair performance.

Before you begin

Make sure the carriage is in the parked position. The carriage and gantry automatically return to
this position after an image is printed. Do not move the carriage or gantry from this position as
this will disable the ink pumps and thus prevent the performance of an ink purge, which is
necessary for printhead maintenance.

NOTE

It is not necessary to turn off the UV lamps as they are shuttered. However, they will be hot if
they are on, so avoid touching them.

Ink must be at the operating temperature of at least 40° Centigrade (104° Fahrenheit) before you
perform printhead maintenance. The Job Control module displays the ink temperature. If the
temperature is low, activate the ink heater by clicking the icon and then monitor the temperature
display.

Equipment

3010104959 Cloth-Poly Wipe 10cmX10cm

Note Attention Caution

CAUTION

The underside of the UV lamps may be hot, avoid touching them. Also, be aware that the

carriage moves up and down during printhead maintenance and there is a crushing hazard if

your hand or arm are placed in the area above the three switches.

IMPORTANT

Do NOT press up too hard on the printhead while you swipe it with the suction-head as this can

dislodge the printhead and require a service call to re-seat the printhead.

NOTE

Maintenance Station Switches:

There are 3 switches inside of the maintenance station . They can be operated in any order. For

example, you can press the second switch to raise the carriage to remove debris from the

underside of the carriage even when a purge isn't required.

1. Switch 1 to purge ink
2. Switch 2 to raise carriage
3. Switch 3 to activate suction pump

Printhead Maintenance

Chapter 11 - Printer Maintenance

175

«
...
173
174
175
176
177
...
»

Содержание Arizona 318 GL

































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Arizona 318 GL

Бренд: QMS Страницы: 2

Бренд: Oki Страницы: 28

Бренд: Oki Страницы: 22

image RUNNER 3045

Бренд: Canon Страницы: 14

Бренд: Oki Страницы: 512

Бренд: Seiko Страницы: 76

Бренд: Avery Dennison Страницы: 13

Бренд: Posnet Страницы: 2

Бренд: Avery Weigh-Tronix Страницы: 40

Бренд: GCC Technologies Страницы: 80

Бренд: Bresser Страницы: 104

Бренд: Epson Страницы: 15

Бренд: Star Micronics Страницы: 73

Бренд: Brother Страницы: 243

Бренд: Brother Страницы: 4

Бренд: Brother Страницы: 112

Бренд: Brother Страницы: 122

Бренд: Brother Страницы: 71

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды