Oce Arizona 318 GL Скачать руководство пользователя страница 184 | Manualshive

Страница: 184 / 224

background image

How to Clean the UV Lamp Filter

Introduction

The top of the housings for the left and right UV lamps contain a filter that keeps dust and other
airborne particles from entering the lamp housings. If the filter becomes clogged with dust and
debris it can cause overheating of the lamps.

When to do

Check the condition of the filters weekly and clean them as needed. If dust accumulates, this can
lead to overheated lamps and results in an error message. Clean the filters at least once every
three months to avoid overheating. If you receive a lamp overheat error, check for dust or debris.
If you get a lamp overheat error and there is no dust on the filter, call for service immediately.

NOTE

When you change a UV lamp bulb, replace the filter.

Before you begin

1. Turn off the ink temperature.
2. Turn off UV lamps.

Required tools

small hand vacuum cleaner

NOTE

Always wear cotton gloves and protective safety glases when handling UV lamps and the

reflecting shutters.

IMPORTANT

Failure to clean the filters can lead to overheating of the lamps and result in a shorter lamp life.

Procedure

1.

Wait for the lamp fans to stop to ensure the housing has cooled down.

2.

Remove the lamp filter by first lifting one corner, then bend it in the center by placing your finger
under the filter and lift it away from the power connector and off the lamp housing.

[132] Remove Lamp Filter

3.

Move away from the printer and use a vacuum cleaner to remove any debris or dust.

How to Clean the UV Lamp Filter

184

Chapter 11 - Printer Maintenance

«
...
182
183
184
185
186
...
»

Содержание Arizona 318 GL

































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Arizona 318 GL

imagePROGRAF iPF760

Бренд: Canon Страницы: 12

imagePROGRAF iPF825 MFP Basic Guide No.1

Бренд: Canon Страницы: 16

imagePRESS C850

Бренд: Canon Страницы: 146

imagePRESS C850

Бренд: Canon Страницы: 63

imagePROGRAF iPF760

Бренд: Canon Страницы: 132

imagePROGRAF iPF825 MFP Basic Guide No.1

Бренд: Canon Страницы: 8

imagePROGRAF TX-2000

Бренд: Canon Страницы: 14

i-SENSYS MF6180dw

Бренд: Canon Страницы: 1040

imagePROGRAF iPF815

Бренд: Canon Страницы: 48

imageRUNNER 1025

Бренд: Canon Страницы: 6

imageRUNNER 2230

Бренд: Canon Страницы: 6

IMAGEPRESS C7010VPS

Бренд: Canon Страницы: 388

Бренд: Canon Страницы: 56

imagePROGRAF iPF8300

Бренд: Canon Страницы: 24

imagePROGRAF iPF8300

Бренд: Canon Страницы: 4

imagePROGRAF iPF6350

Бренд: Canon Страницы: 12

imagePROGRAF iPF6350

Бренд: Canon Страницы: 2

imageCLASS MF8380Cdw

Бренд: Canon Страницы: 192

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды