Oce Arizona 318 GL Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 224

background image

How to Manage Printer Operations

Daily Start-up and Shut-down

Introduction

Keep your printer clean and perform all recommended scheduled maintenance to ensure that the
printer is ready to produce optimal quality images.

When to do

The start-up procedure must be performed every morning or after a period of time when the
printer has not been used. The shut-down procedure indicated here is for the end of a regular
workday. If the printer is shut down for longer periods of time than a few days, then there are
more considerations, as documented in the previous section on How to Switch the Printer Off
(see the note on Extended Power Off).

Start-up Procedure

Procedure

1.

Turn on the ink heater (click on the Ink Temperature Control icon located on the Command
Toolbar of the Job Control screen).

2.

Clean the carriage underside, the and the Ink Spit Tray.

3.

Perform Manual Printhead Maintenance after the ink temperature has reached at least 40° C (104°
F).

NOTE

Refer to the Maintenance chapter for details on how to perform these procedures.

Example

Shut-down Procedure

See the Maintenance chapter for some of the steps below.
• Turn off UV lamps and table vacuum
• Perform Manual Maintenance
• Turn off the ink heater
• Leave the printer powered on.

Daily Start-up and Shut-down - Shut-down Procedure

Procedure

1.

Turn off the UV lamps (click on the lamp icon located on the Command Toolbar of the Job
Control screen).

2.

Turn off the table vacuum.

3.

If it is the end of the work week, swab the printheads.

4.

Turn off the ink heater (click on the Ink Temperature Control icon located on the Command
Toolbar of the Job Control screen).

5.

Do not power off the printer (unless the printer will not used for more than 14 days - in that case
call your service representative).

How to Manage Printer Operations

Chapter 5 - How to Operate Your Océ Arizona Printer

65

«
...
63
64
65
66
67
...
»

Содержание Arizona 318 GL

































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Arizona 318 GL

Бренд: EasyThreed Страницы: 4

Бренд: EASYPRINT Страницы: 37

Perfecta 3600STP

Бренд: Variquest Страницы: 12

Perfecta 3600STP

Бренд: Variquest Страницы: 231

Awards Maker 400

Бренд: Variquest Страницы: 4

Бренд: Xerox Страницы: 11

Бренд: Xerox Страницы: 30

Versant 4100 Press

Бренд: Xerox Страницы: 68

Бренд: Xerox Страницы: 4

Бренд: Xerox Страницы: 4

Бренд: Xerox Страницы: 2

Versant 2100 Press

Бренд: Xerox Страницы: 68

DocuPrint C2200

Бренд: Xerox Страницы: 200

Бренд: Avery Dennison Страницы: 13

Бренд: KIP Страницы: 103

Бренд: Oki Страницы: 4

Бренд: Olivetti Страницы: 22

mC-Print3 MCP31LB

Бренд: Star Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды