Nuvo VISTOR Скачать руководство пользователя страница 60

Страница: 60 / 85

age 60 of 85

5368 KUHL ROAD

●

ERIE, PENNSYLVANIA 16510

●

PHONE 814-899-4220

●

FAX 814-899-1410

A member of the Medical Illumination International Group

Section 6

Fuse Replacement

•

See figures 39 and 40 for fuse location.

Unplug the power cord (floor models) or turn off main power before fuses are

replaced. Failure to do so could result in personal injury and/or property damage.

•

Use a flat blade screwdriver, turn the fuse holder counter-clockwise ¼ turn. Remove the

spring-loaded holder.

•

Replace the blown/broken fuses with Nuvo approved replacement fuses.

Use only Nuvo fuses if replacement is necessary. Failure to do so could result in

personal injury and/or property damage.

To reduce the risk of fire, replace the fuse only with the same type and electrical

rating as indicated on the attached table or on the fuse replacement label.

Note: Do not use light should it continue to blow fuses. Contact the factory

immediately

INPUT VOLTAGE

AMPERAGE RATING

P/N

VistOR PR, VistOR
PRO
(All mounting styles)

115/120 VAC
230/240 VAC

100 VAC

1.50 A, 250V
0.75A, 250 V
1.50 A, 250V

NV0001314
NV0001460
NV0001314

VistOR SP Spotlight
Standard

VistOR SPF Spot
Light
(All mounting styles)

115/120 VAC
230/240 VAC

100 VAC

115/120 VAC
230/240 VAC

2.00 A, 250V

1.00 A, 250 V

2.00 A, 250V

3.50 A, 250V

1.80 A, 250 V

NV0001396
NV0001461
NV0001396

NV0001347
NV0001462

VistOR EX & EXL
(All mounting styles)

115/120 VAC
230/240 VAC

100 VAC

1.50 A, 250V

0.75 A, 250 V

1.50 A, 250V

NV0001314
NV0001460
NV0001314

Содержание VISTOR






















































































Результаты поиска

Содержание VISTOR

Отзывы:

Похожие инструкции для VISTOR

Бренды по названию

Популярные бренды

Nuvo VISTOR, Инструкция по установке и обслуживанию

Результаты поиска

Содержание VISTOR

Отзывы:

Похожие инструкции для VISTOR

Бренды по названию

Популярные бренды