Nuvo VISTOR Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 85

background image

Page 11 of 85

5368 KUHL ROAD

●

ERIE, PENNSYLVANIA 16510

●

PHONE 814-899-4220

●

FAX 814-899-1410

A member of the Medical Illumination International Group

Section 2

VistOR PRO Specifications

Mechanical
Parameter

Value

Weight

Head
Arm
Arm (Floor)
Wall Bracket Assy.
Floor Stand Assy.
Single Ceiling Mount
Dual Ceiling Mount

Approximately 10.10 lbs. (4.58 kg).
Approximately 12.5 lbs. (5.68 kg).
Approximately 11.4 lbs. (5.18 kg).
Approximately 3.00 lbs. (1.36 kg).

Approximately 43.0 lbs. (19.50 kg).
Approximately 14.5 lbs. (6.58 kg).
Approximately 16.0 lbs. (7.26 kg).

Dimensions

Head
Arm
Arm (Floor)
Floor Stand

18” (45.72 cm) Dia. X 6.60 High (16.7 cm)
57.0” (144.8 cm) Long
38.5” (97.79 cm) Long
74.5” (189.23 cm) High

Rotations

Articulating Arm Vertical Movement
Articulating Arm Horizontal Movement

Articulating Arm/Yoke Interface
Yoke/Lamp Head Interface

+/- 40 Degrees travel
Approximately 345 Degrees

Approximately

540 Degrees

Approximately 190 Degrees

Electrical
Parameter

Value

Voltages

Input Voltage

Bulb Voltage

110 - 125 VAC 50/60 Hz
210 - 230 VAC 50/60 Hz
11 – 12 VAC 90 W

Bulb life

2,000 hours (average)

Optical
Parameter

Value

Reflector

16.50” (419.1 mm) diameter, aluminum, multi-facetted

Performance

Color temperature
Focal length
Central illuminance
Light field diameter
Depth of illumination
Light field diameter (d50)
Illuminance (one mask)
Illuminance (two masks)
Illuminance at bottom of standard tube
Illuminance at bottom of standard tube with one mask.
Illuminance at bottom of standard tube with two masks
Irradiance
CRI

4,000 °K
39” (1 meter)
6,520 foot-candles (70,180 Lux)
5.61” (142.5 mm)
42.00” (1067 mm)
3.76” (95.5 mm)
560 foot-candles (6,027 Lux)
1,974.19 foot-candles (21,250 Lux)
6,520 foot-candles (70,180 Lux)
743 foot-candles (7,998 Lux)
1,869.67 foot-candles (20,125 Lux)
81.21 W/m

2

89

Environmental
Parameter

Value

Operating Temperature
Storage Temperature Range

41 -104 ° F (5-40 °Celsius)
42 -113 ° F (5-45 °Celsius)

Humidity

10 - 90% Relative Humidity

«
...
9
10
11
12
13
...
»

Содержание VISTOR






















































































Отзывы:

Нет отзывов

Похожие инструкции для VISTOR

Бренд: XTA Страницы: 29

Бренд: vc999 Страницы: 59

Бренд: Qtx Страницы: 3

Бренд: Saferoad Страницы: 24

Бренд: Raven Страницы: 17

Бренд: Campbell Страницы: 12

Бренд: YASKAWA Страницы: 40

RAISED GARDEN BED

Бренд: Yardfully Страницы: 2

Бренд: Bartscher Страницы: 61

Бренд: Barreto Страницы: 16

FLOOReco 5164-040120

Бренд: DOTLUX Страницы: 10

Aesculap S4 Cervical

Бренд: B. Braun Страницы: 43

Dynamique Biski

Бренд: Enabling Technologies Страницы: 44

PHOTONIA 232075

Бренд: SLV Страницы: 7

Бренд: Jandy Страницы: 52

Бренд: American DJ Страницы: 12

Бренд: aion Страницы: 10

Бренд: COOPS & FEATHERS Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды