Nuvo VISTOR Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 85

background image

P

age 39 of 85

5368 KUHL ROAD

●

ERIE, PENNSYLVANIA 16510

●

PHONE 814-899-4220

●

FAX 814-899-1410

A member of the Medical Illumination International Group

Section 3

Chuttle Track Pre-Installation Requirements

Installation and repair of this equipment should be performed by qualified persons

only. Nuvo, Inc. does not warranty any damage or injuries occurring as a result of
improper installation.

Before installation, check to insure the following conditions are provided and in place.

•

A structural ceiling mount meeting the specifications of the architectural plans, or suggested
structural mounting shown in figures 20 through 23. The installation must be capable of
supporting a weight of at least 200 pounds and an off center load of 500 ft-lbs.

•

The track mount should not be mounted higher than 9 feet 6 inches (9 ½ feet) above the
floor. The track mount must be mounted at the finished ceiling level whether the ceiling
surface is solid or “dropped” type. Mounting the unit higher than 9 ½ feet may result in
instability of the light system and the arm assembly mounted too high to be accessable,

•

Check the length of the ceiling rod supplied (located in the carton with the light head and
arm). The rod lengths available for the Chuttle Track are 16” long for a mounting height of 7
feet 6 inches to 8 feet 6 inches. A 25” long rod is available for a mounting height of 8 feet 7
inches to 9 feet 6 inches. If a problem occurs, contact our service department at (814) 899-
4220 then press 2.

•

The mounting bolts used to fasten the track must be able to support a minimum of 200
pounds each (

3

/

8

” diameter bolts required).

«
...
37
38
39
40
41
...
»

Содержание VISTOR






















































































Отзывы:

Нет отзывов

Похожие инструкции для VISTOR

Бренд: Makerfire Страницы: 10

Бренд: Raymarine Страницы: 464

Бренд: 3M Страницы: 8

Бренд: ZOLL Страницы: 3

Бренд: Taurus Страницы: 28

Бренд: Kärcher Страницы: 54

Бренд: ABB Страницы: 85

Бренд: Campden instruments Страницы: 8

Бренд: Febco Страницы: 12

Бренд: Yetter Страницы: 16

Бренд: Garelick Страницы: 2

Бренд: Gardico Страницы: 2

Бренд: OceanSat Страницы: 85

Бренд: K-LASER Страницы: 70

Бренд: K-LASER Страницы: 72

Бренд: Rane Страницы: 38

Бренд: Kartsana Страницы: 36

Бренд: Mangar International Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды