Nuvo VISTOR Скачать руководство пользователя страница 52

Страница: 52 / 85

age 52 of 85

5368 KUHL ROAD

●

ERIE, PENNSYLVANIA 16510

●

PHONE 814-899-4220

●

FAX 814-899-1410

A member of the Medical Illumination International Group

Section 5

Section 5: Safety Instructions

Safety Tips

Only facility authorized maintenance personnel should troubleshoot the unit.

Troubleshooting by unauthorized personnel could result in personal injury and/or
property damage.

Only facility authorized personnel should repair the unit. Repair by unauthorized

personnel could result in personal injury and/or property damage and could void
warranty.

After completing a repair of the unit, ensure the unit is in proper working order.

Failure to do so could result in personal injury and/or property damage

Use only Nuvo approved replacement lamps (refer to “Lamp Replacement

Instructions” on Section 6). Failure to do so will affect the operating specifications. Use
of a higher wattage lamp may cause a fire hazard, resulting in personal injury and/or
property damage.

Do not touch the lamp or inner glass lens directly. Body oils may significantly lower

the life expectancy of these parts and cause equipment damage.

Follow the product manufacturer’s instructions. Failure to do so could result in

personal injury and/or property damage.

If the unit fails any part of the preventive maintenance functional checks, repair the

unit before use on any patient. Failure to do so could result in personal injury and/or
property damage.

Do not use harsh cleaners, solvents, or detergents. Failure to do so could result in

equipment damage.

Do not use silicone-based lubricants. Equipment damage could occur.

Turn the power off or unplug the power cord before any repairs are started. Failure

to do so could result in personal injury and/or property damage.

Do not pinch any wires during installation or during any repair. Pinched wires can

cause an electrical shock hazard, resulting in personal injury and/or property damage.

Do not expose the unit to excessive moisture. Failure to do so could result in

personal injury and/or property damage.

Содержание VISTOR






















































































Результаты поиска

Содержание VISTOR

Отзывы:

Похожие инструкции для VISTOR

Бренды по названию

Популярные бренды

Nuvo VISTOR, Инструкция по установке и обслуживанию

Результаты поиска

Содержание VISTOR

Отзывы:

Похожие инструкции для VISTOR

Бренды по названию

Популярные бренды