Nustep TRS 4000 Скачать руководство пользователя страница 98

Страница: 98 / 130

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

5. Lift seat channel assembly off.
Remove seat release lever and
swivel release lever.

8. Transfer old swivel release lever
to new bracket and tighten nuts to
80 in-lbs.

Seat Mounting Bracket Assembly

6. Remove the two remaining bolts
that attach seat mounting bracket to
seat and remove seat mounting
bracket.

7. Align holes of new seat mounting
bracket assembly with seat
weldnuts and rear seat lever
springs. Place bracket on seat and
thread two bolts with lockwashers
into front weldnuts. Tighten bolts to
200 in-lbs.

Note: leave rear seat lever springs in
place on seat bottom.

42263 Seat Mounting Bracket Assembly 5-01-05

200 inch-lbs

Torque Setting:

80 inch-lbs

Torque Setting:

Содержание TRS 4000



































































































































Результаты поиска

Содержание TRS 4000

Отзывы:

Бренды по названию

Популярные бренды

Nustep TRS 4000, Руководство по обслуживанию

Результаты поиска

Содержание TRS 4000

Отзывы:

Бренды по названию

Популярные бренды