Nustep TRS 4000 Скачать руководство пользователя страница 28

Страница: 28 / 130

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

Bearings - Shaft

NOTE: This instruction applies to any 1" roller bearing (front left shown).

Tools Required

1/8" hex key
½” socket and ratchet
Flat head screwdriver
Torque wrench

Safety glasses

42009 Bearings - Shaft 5-1-05

5. Loosen set screws.

6. Remove nuts.

To avoid injury, wear safety glasses.

CAUTION

1. Remove covers.

See

Cover Removal

instructions.

2. For S/N < 428173, unhook timing belt springs.

See

Timing Belt Springs

instructions.

For S/N > 428174, unhook belt idler spring.

See

Flat Belt & Belt Idler Spring

instructions.

3. For S/N < 428326, remove poly-v belt.

See

Poly-V Belt

instructions.

For S/N > 428327, remove poly-v J6 flex belt.

See

Poly-V J6 Flex Belt

instructions

4. If removing either left side bearing, remove EC disk and/or poly-v

sheave.

See

EC Disk

and/or applicable

Poly-V Sheave

instructions

Содержание TRS 4000



































































































































Результаты поиска

Содержание TRS 4000

Отзывы:

Бренды по названию

Популярные бренды

Nustep TRS 4000, Руководство по обслуживанию

Результаты поиска

Содержание TRS 4000

Отзывы:

Бренды по названию

Популярные бренды