Nustep TRS 4000 Скачать руководство пользователя страница 73

Страница: 73 / 130

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

Electronic Tube

Tools Required

Phillips screwdriver

Wood block

½” wrench

Torque wrench

1. Remove three screws - and hold
onto display so it doesn’t fall!

2. Release 2 locking tabs on each
side of connector.

Slide boot down tube, then remove
1 screw each side, 1 on bottom.

Snap tabs of connector outward.

3. Pull out cable from connector.

4. Slide both rubber boots up and off
electronic tube.
No photo.

5. Remove 4 bolts that attach
electronic tube and remove tube
from frame carefully letting ribbon
cable come out end.

6. To install, tie washers on end of
string and drop from top through
tube. Tie ribbon cable to string and
carefully pull up through tube.

Remove front cover screw and
carefully spread covers to access bolts.

String with washers attached to ribbon
cable

42035 Electronic Tube 5-01-05

Содержание TRS 4000



































































































































Результаты поиска

Содержание TRS 4000

Отзывы:

Бренды по названию

Популярные бренды

Nustep TRS 4000, Руководство по обслуживанию

Результаты поиска

Содержание TRS 4000

Отзывы:

Бренды по названию

Популярные бренды