manualshive.com logo in svg

Nustep TRS 4000, Руководство по обслуживанию

Поделиться
Скачать
Nustep TRS 4000 Скачать руководство пользователя страница 88

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

Footpedal Support Tube Retaining Ring Removal

Note: This only applies to units with serial numbers of 411001 – 411943.  Removing both lower
retaining rings helps reduce the overall operating tension of the NuStep.  After removal, there
may be a slight gap between the footpedal support tube and the frame, and this is normal.

Tools Required

Snap ring pliers
Safety glasses (for removing ring)

1. Turn NuStep gently onto its left
side (from rider’s perspective).

2.  Remove lower retaining ring from
left footpedal support tube inside
frame.  Do not remove upper ring
near footpedal!

 

 

Note: After removing the ring, the shaft
may snap into the frame and there may
now be a gap on the outside between
the tube and the frame.  This is normal

.

3. Turn NuStep gently onto its right
side.

No photo.

4. Remove lower retaining ring from
right footpedal support tube inside
frame.  Do not remove upper ring
near footpedal!
No photo.

 

42047 FP Support Tube Retaining Ring Removal 5-01-05

80

The TRS 4000 is very heavy; it weighs
205 lbs (93 kg). To avoid injury, or
damage to the product, always obtain
assistance to move this product. Use
proper lifting technique.

To avoid injury, wear safety glasses.

!

 CAUTION

!

 CAUTION

Содержание TRS 4000



































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды