manualshive.com logo in svg

Nustep TRS 4000, Руководство по обслуживанию

Поделиться
Скачать
Nustep TRS 4000 Скачать руководство пользователя страница 58

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

12. Carefully install EC disk onto
shaft and install snap ring.  Snap
ring will slightly preload the bearing,
and Loctite will hold disk in place.

 

14. Install covers.

No photo.

42027 EC Disk & Bearings 5-01-05

EC Disk & Bearings

10. Clean shaft and apply small
amount of Loctite on shaft at 1/2
inch from the tapered end.

11. Place small amount of Loctite on
exterior bearing race.

 

 

13. NOTE: If you are installing the
nut instead of the snap ring, nut
should only bottom out against
shaft shoulder.  Do not tighten nut
so that it preloads the bearings.
Spin the disk and if disk slows
rapidly when tightening nut, back off
so that disk spins freely instead.
Any bearing preload due to the nut
will shorten bearing life.  Loctite will
hold disk in place.

No photo.

To avoid injury and prevent adverse
health effects, use Loctite in
accordance with the manufacturer’s
material safety data sheets, including
the use of safety glasses and
impermeable gloves. Material safety
data sheets are available via the
internet at 

www.loctite.com 

or by

calling Henkel Corporation at (800) 562-
8483.

!

 CAUTION

50

Содержание TRS 4000



































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды