Nustep TRS 4000 Скачать руководство пользователя страница 93

Страница: 93 / 130

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

Seat Armrest (R / L) & Seat Armrest Bracket (R / L)

Tools Required

½” socket and ratchet

9/16" wrench

9/16" socket

1. Remove three bolts that attach
bracket to seat (left side shown).

2. Remove bolt that attaches armrest
to armrest bracket.

3. Replace armrest or armrest bracket at this time. No photo

4. To install, spacers go on each
side of bracket inside armrest. Slide
bolt through from outside in.

5. Tighten nut until armrest moves
smoothly but not too tight or loose.

6. Attach bolts that hold armrest and tighten to 200 in-lbs.

Compare feel
with other side
armrest and
match it.

42079 Seat Armrest and Bracket 5-01-05

To avoid injury, and to ensure safe
operation of this product, fasteners
must be tightened to the proper torque.

CAUTION

200 inch-lbs

Torque Setting:

Содержание TRS 4000



































































































































Результаты поиска

Содержание TRS 4000

Отзывы:

Бренды по названию

Популярные бренды

Nustep TRS 4000, Руководство по обслуживанию

Результаты поиска

Содержание TRS 4000

Отзывы:

Бренды по названию

Популярные бренды