Nustep TRS 4000 Скачать руководство пользователя страница 118

Страница: 118 / 130

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

Swivel Release Lever

42099 Swivel Release Lever 5-1-05

Tools Required

5/32" hex key
Phillips screwdriver
Needle nosed pliers
½” socket and ratchet
Long socket extension
7/16" socket and ratchet
3/8” wrench
Torque wrench
242 Loctite

1. Remove seat assembly.

See

Seat Assembly Removal

instructions.

2. Remove seat release bracket.

For S/N < 428341, see

Seat Release Bracket

instructions.

For S/N > 428342, see

Seat Release Bracket With Stud

instructions.

3. Swivel seat channel assembly 45

°°°°°

to access four bolts that attach seat

channel to seat.

4. Remove four bolts and washers.

To ensure safe operation of this
product, fasteners must be tightened to
the proper torque.

CAUTION

110

Содержание TRS 4000



































































































































Результаты поиска

Содержание TRS 4000

Отзывы:

Бренды по названию

Популярные бренды

Nustep TRS 4000, Руководство по обслуживанию

Результаты поиска

Содержание TRS 4000

Отзывы:

Бренды по названию

Популярные бренды