manualshive.com logo in svg

Nustep TRS 4000, Руководство по обслуживанию

Поделиться
Скачать
Nustep TRS 4000 Скачать руководство пользователя страница 109

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

Seat Release Bracket & Seat Release Spring & Nyliners

42091 Seat Release Brkt & Spring 5-1-05

Tools Required

5/32" hex key
Needle nosed pliers
Torque wrench
242 Loctite
Silicone or white grease
Safety glasses

1. Remove seat assembly.  

See 

Seat Assembly Removal 

instructions.

2. Remove seat release bracket by
removing front and rear shoulder
bolts (rear shown).

3. Remove seat release spring.

4. Replace seat release bracket or spring or Nyliners now (not shown).
Before installing, lubricate bracket along slots and where lever pin contacts
bracket (see old bracket).

 

 

 

 

101

NOTE: This instruction applies to units with S/N < 428341.

To avoid injury, and to
ensure safe operation of
this product, fasteners must
be tightened to the proper
torque.

To avoid injury, wear safety
glasses.

Springs are under tension. To avoid
injury, or damage to the product, use
caution when removing or installing.

!

 CAUTION

!

 CAUTION

!

 CAUTION

Содержание TRS 4000



































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды