manualshive.com logo in svg

Nustep TRS 4000, Руководство по обслуживанию

Поделиться
Скачать
Nustep TRS 4000 Скачать руководство пользователя страница 68

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

42055A Hall Effect Sensor 5-01-05

60

Hall Effect Sensor

NOTE: This sensor and the magnet that passes by it are responsible for indicating
STEPS PER MINUTE, STEPS, TIME, and for turning the display on from its sleep mode.

Tools Required

Phillips screwdriver (long)

2. Disconnect ribbon cable.

3. Disconnect hall sensor wire.

 

 

It makes it easier to access wire.

The red, black, & white wire on right.

4. Unscrew sensor bracket from inside of frame.

5. Remove sensor wiring from cable clips along frame.

 

 

NOTE: Bottom view shown.

 

 

 

 

 

The photo above shows the sensor bracket
used for serial numbers 411001 - 422080.

The photo above shows the sensor bracket
used for serial numbers > 422081.

6. Replace old sensor with new sensor.  No Photo.

The TRS 4000 is very heavy; it weighs
205 lbs (93 kg). To avoid injury, or
damage to the product, always obtain
assistance to move this product. Use
proper lifting technique.

!

 CAUTION

1. Remove covers.  

See 

Cover Removal 

instruction.

Содержание TRS 4000



































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды