Nustep TRS 4000 Скачать руководство пользователя страница 45

Страница: 45 / 130

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

7. Place the front of the belt onto the
hub of the EC disk and rotate the
sheave counter clockwise until the
belt is completely on the sheave and
EC disk hub.

9. Spin poly-v sheave. Belt should
track directly on center of sheave. If
not, move poly-v sheave in or out on
shaft until belt tracks true.

No photo.

8. Cut the zip ties off the sheave.

42068 Poly-V J6 Flex Belt & Sheave Without Grooves 5-1-05

6. To install new belt, secure belt to
sheave using 2 zip ties. Install zip
ties in front of and behind spoke
positioned at 4 o’clock.

Poly-V J6 Flex Belt & Sheave Without Grooves

10. Tighten 2 set screws of poly-v
sheave securely. Install covers.

Belt is under tension. To avoid
injury, or damage to the product,
use caution when removing or
installing.

CAUTION

Содержание TRS 4000



































































































































Результаты поиска

Содержание TRS 4000

Отзывы:

Бренды по названию

Популярные бренды

Nustep TRS 4000, Руководство по обслуживанию

Результаты поиска

Содержание TRS 4000

Отзывы:

Бренды по названию

Популярные бренды