manualshive.com logo in svg

Nustep TRS 4000, Руководство по обслуживанию

Поделиться
Скачать
Nustep TRS 4000 Скачать руководство пользователя страница 10

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

 

Upper Arm (R or L)

NOTE: This instruction applies to all variations of arm locks.  Make sure to use the
screws that came with the kit if you are installing a complete

 

arm assembly.

Tools Required

Phillips screwdriver

1. Loosen knob.

Grease or silicone (white/clear preferred)

2. Remove 2 screws.

NOTE: If you are installing a new arm
assembly, make sure to use the screws
that came with the kit, not the screws
removed here.

4. To install upper arm, do above
steps in reverse order.

B. Wipe a little grease inside top 4" of
lower arm tube before installing.  This
prevents squeaking of arm lock & tube.

D.  When tightening screws in Step 2,
make sure screws go into the holes/
indents on the arm lock, not against it.
The arm lock must float freely.  The
screws keep arm lock from coming out.

3. Slide cap up arm, and then pull
upper arm out of lower arm tube.

INSTALLATION NOTES:

A. Make sure components are properly
installed before installing arm.  

NOTE:

arm lock may be either white or black.

C. The machine key always faces and
comes in contact with the stud end of
the knob and the holes/indents align
with the screws on the bottom of the
tube.  R and L arms tilt inward ~ 20

°

.

Reference Picture:

Cap

Machine Key (may be rectangular or
T shaped)

Holes/indents in arm lock that screws
go into (they do not screw into here)

 

 

 

       Pin           Arm lock (white or black)

 

 

42003 Arm - Upper 7-17-00

 

 

2

Содержание TRS 4000



































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды