Nustep TRS 4000 Скачать руководство пользователя страница 12

Страница: 12 / 130

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

Arm Lock Knob

NOTE: Units with S/N > 411924 do not have a snap ring on the end of the knob stud.
Units < 411924 do, but it is not necessary to reinstall it once removed.

Tools Required

Needle-nosed pliers
Grease/silicone (white/clear)
Safety glasses

2. Remove snap ring from end of
knob stud if it has one. If not,
continue.

3. Thread old knob out. It may be
hard to thread out if it had a snap
ring on it.

No photo.

4. Lubricate threads on new knob
and thread into arm. Wipe up
excess lube. You do not have to
install snap ring back on.
No photo.

5. Install upper arm per instructions.

No photo.

42005 Arm Lock Knob 5-1-05

1. Remove upper arm.

See

Upper Arm

instruction.

To avoid injury, wear safety glasses.

CAUTION

Содержание TRS 4000



































































































































Результаты поиска

Содержание TRS 4000

Отзывы:

Бренды по названию

Популярные бренды

Nustep TRS 4000, Руководство по обслуживанию

Результаты поиска

Содержание TRS 4000

Отзывы:

Бренды по названию

Популярные бренды