Nustep TRS 4000 Скачать руководство пользователя страница 61

Страница: 61 / 130

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

EC Plunger Plate & EC Magnet Slide Bracket

NOTE: These parts come off sequentially. Once you get to the part you need to replace,
replace that part and skip to the other steps as the instruction tells you.

Tools Required

Channel lock pliers

3/4” deep socket and new locking ring

3/16” hex key

Hammer

SIlicone/grease (white or clear)

Safety glasses

2”x4” wood

1. Remove covers.

See

Cover Removal

instructions.

2. Remove poly-v belt or poly-v J6 flex belt.

For S/N < 428325, remove poly-v belt.

See

Poly-V Belt

instructions.

For S/N > 428326, remove poly-v J6 flex belt.

See

Poly-V J6 Flex Belt

instructions.

3. Remove load lever.

See

Load Lever

instructions.

4. Remove self-locking ring. Ring
will be destroyed during this step.

5. Pull plunger plate out of frame.
NOTE: if you are just replacing plunger
GOTO Step 9.

42033 EC Plunger & Slide Brkt 5-01-05

To avoid injury, wear safety glasses.

CAUTION

Содержание TRS 4000



































































































































Результаты поиска

Содержание TRS 4000

Отзывы:

Бренды по названию

Популярные бренды

Nustep TRS 4000, Руководство по обслуживанию

Результаты поиска

Содержание TRS 4000

Отзывы:

Бренды по названию

Популярные бренды