Novatel DL-V3 Скачать руководство пользователя страница 32

Страница: 32 / 116

DL-V3 Firmware Reference Manual Rev 2

Chapter 2

DL-V3 Commands

2.11 GROUPANTHEIGHT

Edit Group Antenna Height

The

groupantheight

command allows you to edit the antenna height definition for the group.

The

groupantheight

set

command sets the antenna height for the group named

groupname

antheight

The

groupantheight

clear

command removes the antenna height setting from the group named

groupname.

The

groupantheight

default

command sets the antenna height for the group to 0

Syntax

groupantheight

set

groupname

[

antheight

]

groupantheight

default|clear

groupname

2.11.1

Groupuse Translation

groupuse start

•

The antenna height setting is reflected in the

groupdef

log.

•

If an automatic site is being generated (see

groupmode

), the group antenna height is used in site

configuration.

groupuse stop

•

Not Applicable (N/A)

Message ID = 66

Table 16: GROUPANTHEIGHT Default Configuration

Field

Data

Value Used if

Not Specified

Bytes

Format

Units

Offset

Header

Parameter Update

, see

Table 23

on Page 41

Enum

none

Group name

Char[]

none

H+4

Antenna height, see

Table 16

Float

none

H+16

Parameter

Power-On

Freset

Stored in NVM

antheight

no change

YES

Содержание DL-V3





















































































































Результаты поиска

Содержание DL-V3

Отзывы:

Похожие инструкции для DL-V3

Бренды по названию

Популярные бренды

Novatel DL-V3, Справочное руководство

Результаты поиска

Содержание DL-V3

Отзывы:

Похожие инструкции для DL-V3

Бренды по названию

Популярные бренды