Novatel DL-V3 Скачать руководство пользователя страница 68

Страница: 68 / 116

DL-V3 Firmware Reference Manual Rev 2

Chapter 2

DL-V3 Commands

2.40 SITEUPDATEATTRIBUTE

Set Occupied Site Attributes

The

siteupdateattribute

command allows you to configure the site attribute information (Attrib field in

the

sitedef

log) once the site has been occupied (by issuing a

site enter

command).

The

siteupdateattribute

set

command sets the site attribute for an occupied site to

attrib.

The

siteupdateattribute

default

and the

siteupdateattribute clear

commands clear the site attribute for

an occupied site

Syntax

siteupdateattribute

set [

attrib

]

siteupdateattribute

default|clear

Message ID = 169

Table 50: SITEUPDATEATTRIBUTE Default Configuration

Field

Data

Value Used if

Not Specified

Bytes

Format

Units

Offset

Header

Parameter Update, see

Table 23 on Page 41

Enum

none

Attribute

Int

none

H+4

Reserved for future use

NUL

Char[]

none

H+8

Parameter

Power-On

Freset

Stored in NVM

Attribute

clear

Содержание DL-V3





















































































































Результаты поиска

Содержание DL-V3

Отзывы:

Похожие инструкции для DL-V3

Бренды по названию

Популярные бренды

Novatel DL-V3, Справочное руководство

Результаты поиска

Содержание DL-V3

Отзывы:

Похожие инструкции для DL-V3

Бренды по названию

Популярные бренды