Novatel DL-V3 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 116

background image

10

DL-V3 Firmware Reference Manual Rev 2

Notices

Notices

Please refer to the

OEMV Family Installation and Operation User Manual

for software license and

warranty information. The following notices apply to the DL-V3.

FCC NOTICE

This equipment has been tested and found to comply with the radiated and conducted emission limits
for a Class A digital device, for both CISPR 22 and Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined
turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:

• Re-orient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment to an outlet on a circuit different from that to which the

receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

WARNING:

Changes or modifications to this equipment not expressly approved by NovAtel
Inc. could result in violation of Part 15 of the FCC rules.

CE NOTICE

The enclosures carry the CE mark.

WARNING:

This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

"Hereby, NovAtel Inc. declares that this DL-V3 is in compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC."

«
...
8
9
10
11
12
...
»

Содержание DL-V3





















































































































Отзывы:

Нет отзывов

Похожие инструкции для DL-V3

Бренд: jablotron Страницы: 3

Бренд: Yaesu Страницы: 195

Бренд: Yaesu Страницы: 39

Бренд: Eonon Страницы: 16

Бренд: FUTABA Страницы: 169

Бренд: Shadow Страницы: 6

Бренд: Spotwave Страницы: 2

Бренд: Alpine Страницы: 78

Бренд: Tactic Страницы: 2

Бренд: Harman Kardon Страницы: 18

Бренд: Boss Audio Systems Страницы: 13

Бренд: Williams Sound Страницы: 8

Бренд: ZGEMMA Страницы: 33

CentreCOM AT-280

Бренд: Allied Telesis Страницы: 4

Бренд: National Страницы: 25

Pro Comm PCX-U1002

Бренд: Peavey Страницы: 36

STARMATE REPLAY ST2

Бренд: Sirius Satellite Radio Страницы: 60

Бренд: Codan Страницы: 164

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды