Novatel DL-V3 Скачать руководство пользователя страница 37

Страница: 37 / 116

DL-V3 Commands

Chapter 2

DL-V3 Firmware Reference Manual Rev 2

Table 20: Parity

Table 21: Handshaking

2.15 GROUPCOMVOUT

Control COM Power for a Group

The

groupcomvout

command allows you to control the peripheral power supply on the COM ports

when a specific group is executed. Command usage is similar to that of the

comvout

command, see

Page 24

, except that a group name argument is required.

The port specifier is the same for the

groupinterfacemode

command, see

Page 42

If you add GROUPCOMVOUT settings to a particular group, they do not take effect until
the next time a GROUPUSE command is run for that group.

If added, each distinct group may have unique settings for GROUPCOMVOUT.

The

groupcomvout

set

command enables you to configure

comvout

behavior for a specific group

(when the group is executed). The interpretation of the

groupcomvout

arguments is the same as that

seen for the

comvout

command.

The

default

action is supported for the

groupcomvout

command. If this argument is supplied, no

changes to the current

comvout

configuration for a peripheral port occurs when the associated group is

executed.

Example:

groupcomvout set mygroup com2 on

groupcomvout set mygroup aux default

The

groupcomvout

clear

command removes the

comvout

configuration for the specified port. The

comvout

configuration for that port is not altered when the group specified in

groupname

is executed.

The

groupcomvout

default command removes

comvout

configurations for all ports. The

comvout

configurations for all ports are not altered when the group specified in

groupname

is executed. This is

equivalent to using the

groupcomvout

set

command to specify

default

for every port.

Binary

ASCII

Description

No parity (default)

Even parity

Odd parity

Binary

ASCII

Description

No handshaking (default)

XON

XON/XOFF software handshaking

CTS

CTS/RTS hardware handshaking

Содержание DL-V3





















































































































Результаты поиска

Содержание DL-V3

Отзывы:

Похожие инструкции для DL-V3

Бренды по названию

Популярные бренды

Novatel DL-V3, Справочное руководство

Результаты поиска

Содержание DL-V3

Отзывы:

Похожие инструкции для DL-V3

Бренды по названию

Популярные бренды