Novatel DL-V3 Скачать руководство пользователя страница 33

Страница: 33 / 116

DL-V3 Commands

Chapter 2

DL-V3 Firmware Reference Manual Rev 2

2.12 GROUPANTSN

Edit Group Antenna Serial Number

The

groupantsn

command allows you to edit the antenna serial number definition for the group.

The

groupantsn

set

command sets the antenna serial number for the group named

groupname

antsn

The

groupantsn

clear

and the

groupantsn

default

commands remove the antenna serial number setting

from the group named

groupname.

Syntax

groupantsn

set

groupname

[

antsn

]

groupantsn

default|clear

groupname

2.12.1

Groupuse Translation

groupuse start

•

The antenna serial number setting is reflected in the

groupdefb

log.

groupuse stop

•

N/A

Message ID = 55

Table 17: GROUPANTSN Default Configuration

Field

Data

Value Used if

Not Specified

Bytes

Format

Units

Offset

Header

Parameter Update, see

Table 23 on

Page 41

Enum

none

Group name

Char[]

none

H+4

Antenna serial number, see

Table 17

NUL

Char[]

none

H+16

Parameter

Power-On

Freset

Stored in NVM

antsn

no change

NUL

YES

Содержание DL-V3





















































































































Результаты поиска

Содержание DL-V3

Отзывы:

Похожие инструкции для DL-V3

Бренды по названию

Популярные бренды

Novatel DL-V3, Справочное руководство

Результаты поиска

Содержание DL-V3

Отзывы:

Похожие инструкции для DL-V3

Бренды по названию

Популярные бренды