Novatel DL-V3 Скачать руководство пользователя страница 22

Страница: 22 / 116

DL-V3 Firmware Reference Manual Rev 2

Chapter 2

DL-V3 Commands

2.1

SYNTAX CONVENTIONS

The following rules apply when entering commands, at the command prompt, from a keyboard.

Courier

font is used to illustrate program output or user input.

References to other commands, logs or any of their fields are shown in

italics

The commands are not case sensitive. For example, you could type either

METTEMP 0

mettemp 0

Except where noted, either a space or a comma can separate commands and their required entries.
For example, you could type either

group del alpha p20a

group,del,alpha,p20a

At the end of a command, a carriage return is required. For example, press <Enter> or <Return>
on your keyboard.

Responses are provided to indicate whether or not an entered command was accepted. The format
of the response depends on the format of the command. Refer to the

OEMV Family Firmware

Reference Manual

for more information.

Optional parameters are indicated by square brackets (

[ ]

). For commands that contain

optional parameters, the value used if the optional parameter is not specified is given in the syntax
table for the command.

Data format definitions, as specified in the “Format” field, are detailed in the

OEMV Family

Firmware Reference Manual

. Note that all binary data is little-endian byte-ordered.

Содержание DL-V3





















































































































Результаты поиска

Содержание DL-V3

Отзывы:

Похожие инструкции для DL-V3

Бренды по названию

Популярные бренды

Novatel DL-V3, Справочное руководство

Результаты поиска

Содержание DL-V3

Отзывы:

Похожие инструкции для DL-V3

Бренды по названию

Популярные бренды