Novatel DL-V3 Скачать руководство пользователя страница 39

Страница: 39 / 116

DL-V3 Commands

Chapter 2

DL-V3 Firmware Reference Manual Rev 2

2.16 GROUPDGPSTXID

Edit Group DGPS ID Configuration

The

groupdgpstxid

command allows you to edit the DGPS base ID configuration for the group. The

group can be configured to store base ID for one DGPS message type.

The

groupdgpstxid

set

command sets the DGPS base ID configuration for the group named

groupname

type

and

(refer to the DGPSTXID command in

the

OEMV Family Firmware

Reference Manual

, for further details on

type

and

The

groupdgpstxid

clear

and the

groupdgpstxid

default

commands remove the DGPS base ID

configuration from the group named

groupname.

Syntax

groupdgpstxid

set

groupname

type ID

groupdgpstxid

default|clear

groupname

2.16.1

Groupuse Translation

groupuse start

•

If set, the

dgpstxid

command is issued.

groupuse stop

•

N/A

Message ID = 271

Field

Data

Bytes

Format

Units

Offset

Header

Parameter Update, see

Table 23 on Page 41

Enum

none

Group name

Char[]

none

H+4

DGPS Type, see

Table 61 on Page 89

and

Table 22

Page 40

Enum

none

H+16

ID, String [max. 5] or

“ANY”

ANY type defaults:
RTCM - 0
RTCMV3 - 0
RTCA - AAAA
CMR - 0
The following range values are in affect:
0

≤

CMR ID

≤

RTCM ID

≤

1023

≤

RTCMV3 ID

≤

4095

RTCA: any four character string containing only alpha
(a-z) or numerical characters (0-9)

Содержание DL-V3





















































































































Результаты поиска

Содержание DL-V3

Отзывы:

Похожие инструкции для DL-V3

Бренды по названию

Популярные бренды

Novatel DL-V3, Справочное руководство

Результаты поиска

Содержание DL-V3

Отзывы:

Похожие инструкции для DL-V3

Бренды по названию

Популярные бренды