Novatel DL-V3 Скачать руководство пользователя страница 27

Страница: 27 / 116

DL-V3 Commands

Chapter 2

DL-V3 Firmware Reference Manual Rev 2

2.6

DEL

Delete Files from CF Card

The

del

command allows you to delete files from the CF card.

The

del all

command deletes all files from the CF card. This operation is not reversible. The

del all

command fails if there are any open files.

The

del file filename

command deletes the file named

file

from the CF card.

File

is a name of a file on

the CF card specified in a

base.ext

format, where

base

is maximum 8 characters and the optional

ext

maximum 3 characters. The

del file filename

command fails if

filename

is open.

Syntax

del all|{file

filename

}

Message ID = 53

Table 11: Delete Target

Field

Data

Bytes

Format

Units

Offset

Header

Delete Target, see

Table 11

Enum

none

File

Char[]

none

H+4

Binary Value

ASCII Value

Description

ALL

Delete all files

FILE

Delete the filename specified

Содержание DL-V3





















































































































Результаты поиска

Содержание DL-V3

Отзывы:

Похожие инструкции для DL-V3

Бренды по названию

Популярные бренды

Novatel DL-V3, Справочное руководство

Результаты поиска

Содержание DL-V3

Отзывы:

Похожие инструкции для DL-V3

Бренды по названию

Популярные бренды