Novatel DL-V3 Скачать руководство пользователя страница 34

Страница: 34 / 116

DL-V3 Firmware Reference Manual Rev 2

Chapter 2

DL-V3 Commands

2.13 GROUPANTTYPE

Edit Group Antenna Type

The

groupanttype

command allows you to edit the antenna type definition for the group.

The

groupanttype

set

command sets the antenna type for the group named

groupname

anttype

The

groupanttype

clear

and the

groupanttype

default

commands remove the antenna type setting from

the group named

groupname.

Syntax

groupanttype

set

groupname

[

anttype

]

groupanttype

default|clear

groupname

2.13.1

Groupuse Translation

groupuse start

•

The antenna type is reflected in the

groupdef

log.

•

If an automatic site is being generated (see

groupmode

Page 46

), the group antenna type is

used in site configuration.

groupuse stop

•

N/A

Message ID = 65

Table 18: GROUPANTTYPE Default Configuration

Field

Data

Value Used if

Not Specified

Bytes

Format

Units

Offset

Header

Parameter Update, see

Table 23

on Page 41

Enum

none

Group name

Char[]

none

H+4

Antenna type, see

Table 18

NUL

Char[]

none

H+16

Parameter

Power-On

Freset

Stored in NVM

anttype

no change

NUL

YES

Содержание DL-V3





















































































































Результаты поиска

Содержание DL-V3

Отзывы:

Похожие инструкции для DL-V3

Бренды по названию

Популярные бренды

Novatel DL-V3, Справочное руководство

Результаты поиска

Содержание DL-V3

Отзывы:

Похожие инструкции для DL-V3

Бренды по названию

Популярные бренды