Novatel DL-V3 Скачать руководство пользователя страница 52

Страница: 52 / 116

DL-V3 Firmware Reference Manual Rev 2

Chapter 2

DL-V3 Commands

2.26 GROUPUSE

Execute a Set of Commands

The

groupuse

command is a macro which uses the group configuration to execute a set of DL-V3

commands.

The

groupuse start

command executes the

start macro

for the group named

groupname,

with the

default log destination set to

dst

. If

dst

is not specified, THISPORT is assumed. If any message-

logging destinations are FILE_

filename

is associated with these destinations. If

filename

is not

specified, it is automatically generated as per the

logfile

command.

The

groupuse start

command interprets the group configuration as follows:

• The

groupuse destination list

is assembled, representing all destinations to be used by the

group.

• For each destination in the groupuse destination list, an

unlogall

command is issued.

• If the groupuse destination list contains any FILE_

, destinations, a

logfile close

command is

issued, closing current logfile (if open).

• For each FILE_

destination in the groupuse destination list, a

logfile

command is issued,

associating the destination with

filename

• The file-header destination,

hdrdst

is selected as the first FILE_

destination in the destination

list. If no FILE_

destination exists, the next 6 sub-steps are omitted.

•

log hdrdst versionb

command is issued.

•

log hdrdst timeb

command is issued.

• If a project has been defined,

log hdrdst projectdefb

command is issued.

• The

currentgroup groupname

command is issued.

• The

log hdrdst groupdefb

command is issued.

• The

currentgroup

command is issued.

•

groupinterfacemode

configuration is executed.

•

groupdgpstxid

configuration is executed

•

groupecutoff

configuration is executed.

•

groupsatlimit

configuration is executed.

•

groupposfix

groupposave

configuration is executed.

• If a file is opened as above,

groupmode

(in conjunction with

groupantheight

groupsitenumber

groupsitename

, and

groupanttype

) configuration is executed.

•

grouplog

configuration is executed.

The

groupuse stop

command executes the

stop macro

for the group named

groupname,

with the

default log destination set to

dst

. If

dst

is not specified, THISPORT is assumed.

The

groupuse stop

command interprets the group configuration as follows:

• The

groupuse destination list

is assembled, representing all destinations to be used by the

group.

Содержание DL-V3





















































































































Результаты поиска

Содержание DL-V3

Отзывы:

Похожие инструкции для DL-V3

Бренды по названию

Популярные бренды

Novatel DL-V3, Справочное руководство

Результаты поиска

Содержание DL-V3

Отзывы:

Похожие инструкции для DL-V3

Бренды по названию

Популярные бренды