Novatel DL-V3 Скачать руководство пользователя страница 47

Страница: 47 / 116

DL-V3 Commands

Chapter 2

DL-V3 Firmware Reference Manual Rev 2

Message ID = 57

Table 28: Group Mode

Table 29: GROUPMODE Default Configuration

2.22 GROUPPOSAVE

Configure Group Position Averaging

The

groupposave

command allows you to configure position averaging to commence when the group

is executed.

groupfixpos

and

groupposave

configurations are mutually exclusive, and the last setting

to be entered takes effect.

The

groupposave

set

command configures the group for position-averaging with parameters set to

maxtime

maxhorstd

and

maxverstd

The

groupposave

clear

and the

groupposave

default

commands clear the group position-average

configuration.

Syntax

groupposave

set

groupname

[

maxtime

[

maxhorstd maxverstd

]]

groupposave

default|clear

groupname

Field

Data

Value Used if

Not Specified

Bytes

Format

Units

Offset

Header

Parameter Update, see

Table 23 on

Page 41

Enum

none

Group name

Char[]

none

H+4

Group Mode, see

Table 28

STATIC

Enum

none

H+16

Binary Value

ASCII Value

Description

STATIC

Set group mode to static

KINEMATIC

Set group mode to kinematic

Parameter

Power-On

Freset

Stored in NVM

Group Mode

no change

KINEMATIC

YES

Содержание DL-V3





















































































































Результаты поиска

Содержание DL-V3

Отзывы:

Похожие инструкции для DL-V3

Бренды по названию

Популярные бренды

Novatel DL-V3, Справочное руководство

Результаты поиска

Содержание DL-V3

Отзывы:

Похожие инструкции для DL-V3

Бренды по названию

Популярные бренды