Novanta v30 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 101

Novanta v30 Скачать руководство пользователя страница 12

GENERAL HAZARDS

PAGE

|

12

•

Caution: Potential hazards or unsafe practices which, if not avoided, may result in product
damage. Alerts operator of equipment dangers.

•

Important Note: Content specific information and/or recommendations.

General hazards

Following are descriptions of general hazards and unsafe practices that could result in death, severe
injury, or product damage. Specific warnings and cautions not appearing in this section are found
throughout the manual.

Lasers should be installed and operated in manufacturing or laboratory facilities by trained personnel
only. Due to the considerable risks and hazards associated with the installation and operational use of
any equipment incorporating a laser, the operator must follow product warning labels and instructions to
the user regarding laser safety. To prevent exposure to direct or scattered laser radiation, follow all
safety precautions specified throughout this manual and exercise safe operating practices per ANSI
Z136.1-2014, Safe Use of Lasers always when actively lasing.

Due to the specific properties of laser light, a unique set of safety hazards that differ from other light
sources must be considered. Just like light, lasers can be reflected, refracted, diffracted, or scattered.

Warning: Serious Personal Injury

For laser systems being used or sold within the U.S.A., customers should refer to and follow the laser
safety precautions described American National Standards Institute (ANSI) document Z136.1-2014,
Safe Use of Lasers.

For laser systems being used or sold outside the U.S.A., customers should refer to and follow the laser
safety precautions described in European Normative and International Electrotechnical Commission
documents IEC/ TR 60825-14:2014, Safety of Laser Products – §14: A User’s Guide.

«
...
10
11
12
13
14
...
»

Содержание v30






































































































Отзывы:

Нет отзывов