Nordson Encore HD iControl 2 Скачать руководство пользователя страница 86

Страница: 86 / 114

1609758-04

5-2

Repair

Spray Gun Control Card Removal/Installation

Replacing a Spray Gun Control Card

WARNING:

Do not remove spray gun control cards from the card cage while they are

powered. Either shut off console power or shut off the booth exhaust fan so that the

interlock will remove power from the spray gun control cards. Failure to observe this

warning could result in damage to the cards.

CAUTION:

Do not turn off console power without first performing a program shutdown.

Doing so could corrupt the iControl 2 program and operating system on the program

card. Refer to

Program Shutdown in the Configuration

section of the

iControl Operator

Interface

manual for the shutdown procedure.

CAUTION:

The spray gun control cards are electrostatic sensitive devices (ESD). To

prevent damage to the cards when handling them, wear a grounding wrist strap

connected to the iControl 2 enclosure or other ground. Handle the cards only by their top

and bottom edges.

See Figure 5-1. Spray gun control cards (2) are installed in the card cage from left to

right. Each card controls two spray guns: the bottom receptacle is the odd spray gun

number; the top receptacle is the even spray gun number.
To remove a card, disconnect the spray gun harness connectors (3 and 4), pull down the

locking tab (5), then pull the card out of the card cage.
To install a new card, slide the card into the slots in the card cage and seat the card’s

finger board firmly into the connector slot on the backplane (6). Push the locking tab up

to lock the card into the card cage. Connect the spray gun harness to the two receptacles

on the card.

Adding Spray Guns

If the console has an odd number of spray guns, it is possible to add another spray gun

without adding another spray gun control card. If the console has an even number of

spray guns less than 16, add more spray guns by installing a new spray gun control

card in an unused slot. Refer to

System Upgrades

in the Installation section for more

information on adding spray guns to an existing system.

For either scenario, open the Guns and Consoles configuration screen, increase

the number of spray guns, and reboot the system before the new spray guns will be

recognized.

NOTE:

Cards are installed in the card cage from left to right. Spray guns are numbered

from left to right and bottom to top.

Содержание Encore HD iControl 2



















































































































Результаты поиска

Содержание Encore HD iControl 2

Отзывы:

Похожие инструкции для Encore HD iControl 2

Бренды по названию

Популярные бренды

Nordson Encore HD iControl 2, Установка, устранение неисправностей, ремонт

Результаты поиска

Содержание Encore HD iControl 2

Отзывы:

Похожие инструкции для Encore HD iControl 2

Бренды по названию

Популярные бренды