Nordson Encore HD iControl 2 Скачать руководство пользователя страница 60

Страница: 60 / 114

1609758-04

4-10

Troubleshooting

Spray Gun Card LEDs

See Figure 4-1. Use the card LEDs to help diagnose problems.

Table 4-4 Spray Gun Card LEDs

LED

Color

Function

Correction

Fault

Red

Lights when a

fault is detected

(communication,

spray gun cable,

RAM, or hardware).

If two spray guns are not connected to the card this LED

will light. If you have an odd number of spray guns in the

system, unplug the unused harness and install the jumper

plug shipped with the console. (Refer to

Odd Number of

Spray Guns

below or the Installation section.) Make sure

the card is seated in the backplane. Open the Alarm screen

and clear all faults. Replace the card if the malfunction

cannot be corrected.

Status

Green

Flashing (heartbeat)

when communicating

properly with system.

If the status LED is not flashing, make sure the card is

seated in the backplane. Turn console power off and on.

Replace the card if the other spray gun control cards have

heartbeats.

Gun Limit B (even-

numbered spray gun

Yellow

Lights if over-current

protection circuit

triggered due to high

current draw from

spray gun drive circuit.

Refer to the corrections for Fault Code E15 in Table 4-3.

Gun Limit A (odd-

numbered spray gun)

Power

Green

Lights when power (5

volts) is applied to the

board).

If the card has no power, make sure it is properly seated

in the backplane and the locking tab is working correctly.

Replace the card if the other spray gun control cards have

power.

Содержание Encore HD iControl 2



















































































































Результаты поиска

Содержание Encore HD iControl 2

Отзывы:

Похожие инструкции для Encore HD iControl 2

Бренды по названию

Популярные бренды

Nordson Encore HD iControl 2, Установка, устранение неисправностей, ремонт

Результаты поиска

Содержание Encore HD iControl 2

Отзывы:

Похожие инструкции для Encore HD iControl 2

Бренды по названию

Популярные бренды