Nordson Encore HD iControl 2 Скачать руководство пользователя страница 57

Страница: 57 / 114

1609758-04

4-7

Troubleshooting

Code

Message Text

Description

Refer to

Page

2108

Speed calculated greater

than maximum

The speed of the reciprocator is greater than the maximum

value allowed.

page 4-26

2113

Reciprocator not in ready

state for Color Change

The reciprocator is not in the proper position for color change. page 4-26

300x

Watchdog

3100

Positioner Watchdog fault

The remote Ethernet device did not respond with a watchdog

signal in 1 second.

page 4-18

3200

Reciprocator Watchdog fault The remote Ethernet device did not respond with a watchdog

signal in 1 second.

page 4-26

410x

Color Change

4109

Clean cycle aborted arch

clean operation − waiting on

park release

Clean cycle detected an abort − waiting for user to press park

to release.

page 4-18

4110

Clean cycle aborted by

user action − park release

detected

Clean cycle aborted by user − part release was detected.

page 4-18

4111

Clean cycle aborted

detected machine lockout/

watchdog

A machine malfunction aborted the cleaning operation.

page 4-18

CAN Network Errors

Table 4-2 CAN Network Messages

Error

Code

Message

Cause/Correction

101

CAN bus fault detected

Hardware error. Check the CAN cable for shorts. If the cable is good,

replace the CAN card.

102

CAN receive buffer overflow

Host CAN interface received too much data and could not process it

quickly enough. Reboot the system.

103

Message timeout

Remote CAN device did not respond to a direct request in the allotted

time. Check the spray gun card or iFlow card.

104

Went offline

Normal operational message. The user will see this message if the

booth exhaust fan is shut off, which removes power from spray gun

cards, or if the spray gun card is disconnected, or if the iFlow module is

disconnected from the CAN network.

105

Returned to online

Normal operational message. No action required.

107

Communications errors

These error messages indicate that communications on the iControl

2 CAN bus may be having problems. Troubleshooting should include

verification of all CAN cable connections and grounding, and spray gun

cable connections and continuity. CAN errors can also be caused by

individual spray gun cards or the iControl 2 PC to CAN card interface.

These errors do not indicate a specific device failure as all devices are in

parallel on the CAN bus.

108
109

110

111

112
113

Содержание Encore HD iControl 2



















































































































Результаты поиска

Содержание Encore HD iControl 2

Отзывы:

Похожие инструкции для Encore HD iControl 2

Бренды по названию

Популярные бренды

Nordson Encore HD iControl 2, Установка, устранение неисправностей, ремонт

Результаты поиска

Содержание Encore HD iControl 2

Отзывы:

Похожие инструкции для Encore HD iControl 2

Бренды по названию

Популярные бренды