Nordson Encore HD iControl 2 Скачать руководство пользователя страница 44

Страница: 44 / 114

1609758-04

3-20

Installation

MAC Addresses

Record the MAC addresses and functions for each Ethernet node in the analog scanner

junction box and main electrical control panel, or any other panels, as they will be needed

when configuring the iControl 2 software.

The MAC addresses are on the node labels, in the form 0:30:DE:0:33:C8. Each

PLC node can control two positioners, a positioner/reciprocator combination, or two

reciprocators.

Spray Gun Cable Connections

See Figure 3-11. Connect the automatic spray gun cables to the receptacles on the rear

panel of the iControl 2 console. Connect spray gun 1 cable to receptacle 1, spray gun 2

cable to receptacle 2, and so on.

Odd Number of Spray Guns

iControl 2 systems are sold configured for an even number of spray guns. Each spray

gun controller card in the console controls two spray guns. If the system is configured

for an odd number of spray guns, the fault LED on the card with only one spray gun

connected will light.

NOTE:

The unused spray gun must be the highest even-number spray gun. For

example, if there is an 8-spray gun system, then number 8 must be the unused spray

gun. The spray gun card receptacles are labeled on the circuit boards as A (odd-number

spray gun) and B (even-number spray gun).

Included in the bag with the console keys is a bulkhead seal and jumper. The jumper

disables the spray gun not detected fault LED on the spray gun card.
Cap the unused cable receptacle with the bulkhead seal, then open the console door

and unplug the receptacle harness from the spray gun card. Install the jumper in the card

receptacle.
Refer to the

Parts

section for seal and jumper part numbers.

Содержание Encore HD iControl 2



















































































































Результаты поиска

Содержание Encore HD iControl 2

Отзывы:

Похожие инструкции для Encore HD iControl 2

Бренды по названию

Популярные бренды

Nordson Encore HD iControl 2, Установка, устранение неисправностей, ремонт

Результаты поиска

Содержание Encore HD iControl 2

Отзывы:

Похожие инструкции для Encore HD iControl 2

Бренды по названию

Популярные бренды