Nordson Encore HD iControl 2 Скачать руководство пользователя страница 65

Страница: 65 / 114

1609758-04

4-15

Troubleshooting

Error

Code

Message/Condition

Meaning/Correction

911

TCP port not available

Programming error. Contact Nordson technical support.

917

Checksum error

Noise in network. Check for loose connections or Ethernet cables routed

parallel to high voltage or VFDs.

918

Invalid frame error

Noise in network. Check for loose connections or Ethernet cables routed

parallel to high voltage or VFDs.

919

Invalid reply error

Noise in network. Check for loose connections or Ethernet cables routed

parallel to high voltage or VFDs.

920

Reply time-out

Noise in network. Check for loose connections or Ethernet cables routed

parallel to high voltage or VFDs.

921

Modbus exception

response

Programming error or remote hardware error. Check PLC functions.

925

Illegal Function exception

response

Programming error or remote hardware error. Check PLC functions.

926

Illegal Data Address

exception response

Programming error or remote hardware error. Check PLC functions.

927

Illegal Data Value

exception response

Programming error or remote hardware error. Check PLC functions.

928

Slave Device Failure

exception response

Programming error or remote hardware error. Check PLC functions.

−

Watchdog Fault (any

remote node controller

fault)

Control program in PLC is not running, or controller has no program installed.

NOTE:

This fault may be a normal response to removing electrical power from

the remote node.
Check the PLC mode selection switch. The switch should be in the run (up)

position.
Replace the PLC. The replacement must be pre-programmed or a program

must be downloaded and installed in the field.

Contact Nordson Industrial Coating Systems Customer Support for details.

−

Operation was successful Normal operation. No action required.

−

Illegal argument error

Programming error. Contact Nordson technical support.

−

Illegal state error

Programming error. Contact Nordson technical support.

−

Evaluation expired

Programming error. Contact Nordson technical support.

−

I/O error class

Programming error. Contact Nordson technical support.

Fieldbus protocol error

class

Programming error. Contact Nordson technical support.

Содержание Encore HD iControl 2



















































































































Результаты поиска

Содержание Encore HD iControl 2

Отзывы:

Похожие инструкции для Encore HD iControl 2

Бренды по названию

Популярные бренды

Nordson Encore HD iControl 2, Установка, устранение неисправностей, ремонт

Результаты поиска

Содержание Encore HD iControl 2

Отзывы:

Похожие инструкции для Encore HD iControl 2

Бренды по названию

Популярные бренды