Nordson Encore HD iControl 2 Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 114

background image

© 2022 Nordson Corporation

4-32

Troubleshooting

Calibration with a Mouse

WARNING:

Do not spray powder while the console door is open. Shut off the booth

exhaust fan to remove switched power from the console and prevent spray gun opera-

tion while performing this procedure. Failure to observe this warning could create a

hazardous condition and could result in personal injury or property damage.

Use this procedure to recalibrate the touch screen if unable to touch the CAL button or

the buttons on the iControl 2 screens, or if installing a program card previously used in

another iControl 2 console.

1.

Turn off the iControl 2 console power.

2. Open the iControl 2 console door and connect a USB mouse to the iControl 2 PC.
3. Turn on power and allow the operating system to load. The CAL button is displayed

on the touch screen before the iControl 2 software loads.

4. Use the mouse to move the cursor to the CAL button and click on it. The touch screen

calibration procedure starts.

NOTE:

If the CAL button was missed, allow the iControl 2 software to load, then, if

possible, open the System Configuration screen and touch the Program Shutdown

button. When the operating system shutdown prompt appears on the screen, touch the

Cancel button, then the CAL button. If unable to touch any buttons on the screen, then

cycle the console power and try again (go back to Step 1).

5. Once the calibration procedure starts, USE YOUR FINGER, NOT THE MOUSE, to

touch the calibration targets, following the instructions on the screen carefully. When

you have completed the calibration procedure, touch the iControl 2 button to start the

iControl 2 software.

6.

Test the touch screen calibration, then perform a program shutdown, turn off console

power, and disconnect the mouse. Close the iControl 2 cabinet door before restarting

the system.

No Touch Screen Display

Check the following:

• Check the power LED on the front bezel below the screen. If the LED is not lit then the

PC is not powered up.

• Make sure the system power switch is on.
• Make sure the video and serial cables between the PC and the touch screen is

connected.

Have an electrician check the following:

• Console fuses on the DIN rail, at the incoming power terminals
• Unswitched power connections to the fuse blocks
• Power supply to the console
• 12 Vdc supply to the touch screen
• 24 Vdc supply to the PC

«
...
80
81
82
83
84
...
»

Содержание Encore HD iControl 2



















































































































Отзывы:

Нет отзывов

Похожие инструкции для Encore HD iControl 2

Бренд: QUAD Страницы: 16

Бренд: MADRIX Страницы: 36

Бренд: Unipulse Страницы: 99

Бренд: Accutrol Страницы: 25

Бренд: Mainpine Страницы: 16

Бренд: Danfoss Страницы: 20

Бренд: Rachio Страницы: 2

Бренд: Lawler Страницы: 4

Бренд: QTP Страницы: 2

Бренд: WAGO Страницы: 18

Бренд: WAGO Страницы: 46

Q Module WFZ16.Ox

Бренд: QUNDIS Страницы: 24

CWDM-CR-B Series

Бренд: Lantronix Страницы: 19

Бренд: Netafim Страницы: 4

Бренд: TREND Страницы: 12

HmIP-FAL230-C10

Бренд: HomeMatic Страницы: 42

Бренд: Joy-it Страницы: 7

Бренд: Woodward Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды