Nordson Encore HD iControl 2 Скачать руководство пользователя страница 47

Страница: 47 / 114

1609758-04

3-23

Installation

In addition to the configuration data, up to 255 presets per spray gun can be stored on

one data card. Additional cards provide virtually unlimited number of presets. To back up

a data card, use the Data Backup function. This copies the data to a blank card. Refer to

Data Backup

in the

iControl Operator Interface

manual for instructions.

NOTE:

Not all CompactFlash cards are the same. When additional cards are

purchased, make sure they are from a Nordson-approved manufacturer and are 128 Mb

or greater. For approved CF cards, refer to

Specifications

in the

Description

section of

this manual or contact your Nordson controls engineer or Nordson Technical Support.

Touch Screen Calibration

The touch screen is calibrated at the factory before the system is shipped. The touch

screen calibration values are stored on the program card. If installing a new program card

that has never been used before, there will be no calibration file on the card. The system

will automatically start the calibration procedure.
Follow the calibration instructions on the screen exactly by using the targets on the touch

screen. When the calibration procedure is complete, touch the iControl 2 button to start

the

iControl 2

software.

Refer to

Troubleshooting

for a complete description of the calibration procedure and

instructions on calibration.

System Upgrades

iControl 2 systems can be upgraded by:

•

installing a new program flash card with updated software.

• adding additional spray guns to an existing console.
• adding an auxiliary console.
• adding an air conditioner to the console to keep the electronics cool.

Certain upgrades require updates to the spray gun control card and iFlow module

firmware. These upgrades should only be done by a Nordson representative.

Содержание Encore HD iControl 2



















































































































Результаты поиска

Содержание Encore HD iControl 2

Отзывы:

Похожие инструкции для Encore HD iControl 2

Бренды по названию

Популярные бренды

Nordson Encore HD iControl 2, Установка, устранение неисправностей, ремонт

Результаты поиска

Содержание Encore HD iControl 2

Отзывы:

Похожие инструкции для Encore HD iControl 2

Бренды по названию

Популярные бренды