Nordson Encore HD iControl 2 Скачать руководство пользователя страница 55

Страница: 55 / 114

1609758-04

4-5

Troubleshooting

Code

Message Text

Description

Refer to

Page

90x

Ethernet Networking

901

I/O error

Ethernet I/O communication failure.

page 4-14

902

POrt or socket open error

The Ethernet connection failed to open for service.

page 4-14

903

Serial port already open

The Ethernet connection is already open and received an

open command.

page 4-14

904

TCP/IP connection error

Unable to connect to remote device.

page 4-14

905

TCP/IP connection was

closed by remote peer

Remote device closed the I/O connection.

page 4-14

906

Socket library error

The socket library returned error status.

page 4-14

907

TCP Port already bound

Requested TCP port is in use by another application.

page 4-14

908

Listen failed

The local system cannot detect activity on the Ethernet

network.

page 4-14

909

File descriptors exceeded

Too many connections are open.

page 4-14

910

No permission to access

serial or TCP port

The program requesting the Ethernet resource does not have

permission to do so.

page 4-14

911

TCP Port not available

The requested port is busy or otherwise not available.

page 4-15

917

Checksum error

Data packets were received with errors.

page 4-15

918

Invalid frame error

Data packets were received with errors.

page 4-15

919

Invalid reply error

Data packets were received with errors.

page 4-15

920

Reply time-out

A reply to a request was not received in time.

page 4-15

921

Modbus exception response An illegal Modbus command was detected.

page 4-15

925

Illegal Function exception

response

An illegal function call was detected.

page 4-15

926

Illegal Data Address

exception response

An illegal address was detected.

page 4-15

927

Illegal Data Value exception

response

An illegal data value was detected.

page 4-15

928

Slave Device Failure

exception response

The slave device returned an exception.

page 4-15

Continued...

Содержание Encore HD iControl 2



















































































































Результаты поиска

Содержание Encore HD iControl 2

Отзывы:

Похожие инструкции для Encore HD iControl 2

Бренды по названию

Популярные бренды

Nordson Encore HD iControl 2, Установка, устранение неисправностей, ремонт

Результаты поиска

Содержание Encore HD iControl 2

Отзывы:

Похожие инструкции для Encore HD iControl 2

Бренды по названию

Популярные бренды