Nordson Encore HD iControl 2 Скачать руководство пользователя страница 58

Страница: 58 / 114

1609758-04

4-8

Troubleshooting

Spray Gun Card Troubleshooting

Refer to Figure 4-1 and Table 4-3 and Table 4-4. Use the fault codes on the Spray Gun

Control screens, the fault messages on the Alarm screen, and the LEDs on the spray gun

control cards to diagnose problems with the spray gun control cards.

Spray Gun Card Error Codes and Fault Codes

These faults, except for E16, will activate the alarm relay.

Table 4-3 Spray Gun Card Error and Fault Codes

Error

Code

Message

Fault

Code

Meaning/Correction

301

Micro-Amp fault

detected

−

Micro-amp value out of range.

302

Over-current fault

detected

E15

Over-current detected. Clear the fault, unplug the cable from the spray gun

and trigger the spray gun.

• If the fault changes to E7, check the resistance of the multiplier as

described in the spray gun manual.

• If the fault code stays E15, check the continuity of the cable as described

in the spray gun manual.

303

Feedback fault

detected

Micro-amp feedback not detected. Check the spray gun current with no

parts in front of the spray gun. If the current is 105

A, check for a short

circuit of the current feedback wires in the spray gun cable:
Unplug the cable from the spray gun and trigger the spray gun.

• If the fault stays E3, replace the cable.
• If the fault changes to E7, check the resistance of the multiplier as

described in the spray gun manual.

304

Open circuit

detected

Spray gun cable or multiplier open circuit. If the current display is 1

A or less, check the multiplier cable and electrode assembly for loose

connections.

• If the connections are secure, check the multiplier with an ohmmeter as

described in the spray gun manual.

• If the multiplier reading is acceptable, check for a defective cable as

described in the spray gun manual.

305

Short circuit

detected

Spray gun cable or multiplier short circuit. Unplug the cable from the spray

gun and trigger the spray gun.

• If the fault changes to E7, check the resistance of the multiplier as

described in the spray gun manual.

• If the fault code stays E8, check the continuity of the cable as described

in the spray gun manual.

Continued...

Содержание Encore HD iControl 2



















































































































Результаты поиска

Содержание Encore HD iControl 2

Отзывы:

Похожие инструкции для Encore HD iControl 2

Бренды по названию

Популярные бренды

Nordson Encore HD iControl 2, Установка, устранение неисправностей, ремонт

Результаты поиска

Содержание Encore HD iControl 2

Отзывы:

Похожие инструкции для Encore HD iControl 2

Бренды по названию

Популярные бренды