Nordson Encore HD iControl 2 Скачать руководство пользователя страница 24

Страница: 24 / 114

1609758-04

2-12

Overview

Approved Program and User Data Cards

CompactFlash card capacity: 512 Mb minimum − Type I CompactFlash only.

NOTE:

Retail CompactFlash refers to devices available at camera, computer, and

electronic retail shops. Retail flash has a rating of 30,000 to 600,000 write cycles at a

maximum of 75°C (167°F) and may experience a shorter overall life.

Industrial

CompactFlash refers to rated devices only available through an electronics

parts supplier and online sources that sell CompactFlash with an industrial temperature

rating for use in Embedded Systems. Industrial flash has a rating of 2,000,000 write

cycles and an increased temperature range to 85°C (185°F).

NOTE:

Both the Program and Data cards should be the same size and from the same

manufacturer. If they are not of the same size, the system may not boot properly.

NOTE:

The SwissBit 2 Gb is the only validated card for Rev 2 Arbor PC, which requires

a minimum of a 2 Gb CompactFlash.

Validated cards:

•

Dane−Elec − retail to 512 Mb

•

Kingston Technology − retail to 4 Gb

•

PNY − retail to 2 Gb

•

SanDisk − retail to 2 Gb, industrial to 1 Gb

•

SanDisk − industrial 4 Gb or larger (must be used in pairs)

•

Silicon Systems − industrial 512 Mb

•

Smart Modular Technologies − industrial to 1 Gb

•

SMC Numonyx − industrial to 1 Gb

•

SwissBit − industrial 2 Gb

•

Transcend − industrial 512 Mb

•

Toshiba − retail to 2 Gb Incompatible cards:

•

LEXAR − any

•

Type II Compact Flash − any (cards will not fit in card slot)

Содержание Encore HD iControl 2



















































































































Результаты поиска

Содержание Encore HD iControl 2

Отзывы:

Похожие инструкции для Encore HD iControl 2

Бренды по названию

Популярные бренды

Nordson Encore HD iControl 2, Установка, устранение неисправностей, ремонт

Результаты поиска

Содержание Encore HD iControl 2

Отзывы:

Похожие инструкции для Encore HD iControl 2

Бренды по названию

Популярные бренды