Nordson Encore HD iControl 2 Скачать руководство пользователя страница 64

Страница: 64 / 114

1609758-04

4-14

Troubleshooting

Ethernet Network Troubleshooting

All Ethernet Network faults will activate the alarm relay. Use the fault messages on the

Alarm screen along with this table to diagnose and correct Ethernet network problems.

Use the Network Status and Node Configuration screens to diagnose problems with the

remote nodes.

Table 4-5 Ethernet Network Troubleshooting

Error

Code

Message/Condition

Meaning/Correction

901

I/O error

Check Ethernet wiring. Remote node could be disconnected from network or

turned off.

902

Port or socket open error

Programming error. Contact Nordson technical support.

903

Serial port already open

Programming error. Contact Nordson technical support.

904

TCP/IP connection error

Check Ethernet wiring. Remote node could be disconnected from network or

turned off.

905

TCP/IP Connection closed

by remote peer fault (any

remote node fault)

Ethernet network communication with the remote node has been lost. This fault

may be a normal response to removing electrical power from the remote node.

If the remote node is an in/out positioner or reciprocator and communication is

lost while operating in Auto mode, the machine will move to the Park position.
Check the Network Node Status screen. If communication is lost the node icon

should turn red. If no nodes are red, check the Network Node Configuration

screen to find the device associated with the faulted node IP address.

If multiple node faults are displayed:

Check the electrical power supply to all faulted nodes.
Check the Ethernet switch in the main electrical control panel for electrical

power and proper operation. The switch power LED should be lit and the

network connection LEDs should be flashing. Replace the switch if necessary.

Check the network cable and connections between the Ethernet switch and the

iControl 2 PC.

If a single node fault is displayed:

Check the electrical power to the remote node.
Check network cables and connections between the remote node and the

Ethernet switch in the main electrical control panel.

906

Socket library error

Programming error. Contact Nordson technical support.

907

TCP port already bound

Programming error. Contact Nordson technical support.

908

Listen failed

Programming error. Contact Nordson technical support.

909

File descriptors exceeded Programming error. Contact Nordson technical support.

910

No permission to access

serial or TCP port

Programming error. Contact Nordson technical support.

Continued...

Содержание Encore HD iControl 2



















































































































Результаты поиска

Содержание Encore HD iControl 2

Отзывы:

Похожие инструкции для Encore HD iControl 2

Бренды по названию

Популярные бренды

Nordson Encore HD iControl 2, Установка, устранение неисправностей, ремонт

Результаты поиска

Содержание Encore HD iControl 2

Отзывы:

Похожие инструкции для Encore HD iControl 2

Бренды по названию

Популярные бренды