Nordic ID Morphic Скачать руководство пользователя | Manualshive

Страница: 7 / 58

background image

Battery

Use only original, Nordic ID approved rechargeable batteries being intended for the Nordic ID
Morphic to avoid serious health hazards to you or to your fellow-men, or damage to the
surrounding property and to your device.

Battery

Caution:

Under no circumstances must you disassemble the battery casing or damage it. If the

battery casing is damaged, for example, the joint of the casing is opened when the battery
has fallen onto the floor, dispose of the battery.

If there is any difference from what is usual or expected on the battery such as a change in

normal shape, smell of electrolyte, and an electrolyte leakage, do not use the battery any
longer, and dispose of it.

Do not put the battery into any liquid.

Care shall be taken to handle, or to store the rechargeable battery so that the battery’s

electrical conductors do not short-circuit. The short circuit causes damage to the battery.

Do not expose the rechargeable battery to direct sunlight or to other heat sources. The

battery temperature cannot go up over 60°C (140°F) without possible consequences for the
battery’s useful life. The higher temperature may cause damage to the battery, which
makes the battery unusable. 100°C (212°F) or higher temperature can cause a battery
explosion.

Keep the battery out of the reach of children

Nordic ID International Headquarters

Myllyojankatu 2A
FI-24100 SALO
FINLAND

Phone:

+358 2 727 7700

Fax:

+358 2 727 7720

Email: [email protected]

www.nordicid.com

«
...
5
6
7
8
9
...
»

Содержание Morphic



























































Отзывы:

Нет отзывов

Похожие инструкции для Morphic

QuickScan I QM21X1

Бренд: Datalogic Страницы: 362

Бренд: Datalogic Страницы: 2

Бренд: Datalogic Страницы: 67

Бренд: Datalogic Страницы: 314

Бренд: Datalogic Страницы: 4

QuickScan Lite QW2100

Бренд: Datalogic Страницы: 24

Бренд: ICT Страницы: 7

Бренд: Symbol Страницы: 112

Бренд: Unitech Страницы: 99

Imperial Digiplex Evo R915

Бренд: Paradox Страницы: 4

Бренд: TriCoder Страницы: 2

Бренд: Nordic ID Страницы: 38

Бренд: Nordic ID Страницы: 45

Бренд: ZKTeco Страницы: 4

Бренд: ZKTeco Страницы: 27

Бренд: Opticon Страницы: 42

Бренд: Manhattan Страницы: 2

Бренд: RIOTEC Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды