Nordic ID Morphic Скачать руководство пользователя | Manualshive

Страница: 12 / 58

background image

Whatever the thickness of the battery is, installing the battery remains the same. The following
series of pictures depicts battery installation in its compartment on the device.

STEP 1:

Open battery cover

STEP 2:

Put battery into its

compartment

STEP 3:

Close battery cover

2.3 About the lithium-polymer battery

Note

that the lithium-polymer rechargeable battery included in the box is not fully charged. Before

first-time use of the device the battery must be fully charged.

Note

that it is strongly recommended to charge the lithium-polymer battery indoors at 20°C

temperature, or at temperature near that (

r

2°C), because continual charging at high or low

temperature may cause degradation of battery performance even within specified temperature
range, which is 0 to 45 degrees Celsius.

Note

that every charge/discharge cycle has an effect on the rechargeable battery’s ampere-hour

capacity, so that the fully charged battery, which is charged many times before, runs down more
rapidly in use than the battery just brought into use. After 500 charge/discharge cycles, if the
battery has been run with care enough, the battery’s ampere-hour capacity is still more than two-
thirds of its original one. However, the charge/discharge cycle is a conception being not
unambiguous. Accordingly, between short operating periods it is not reasonable to recharge the
battery.

Note

that ambient temperature has an effect on how long the fully charged lithium-polymer battery

is able to power your device. A rule of thump is that the colder is using conditions the shorter is
operating time of the device powered by the fully charged battery.

Note

that if the battery runs down, do not leave the device with the flat battery or the battery which

has run down lying idle without recharging the battery, because the battery may be overdischarged
due to self discharge. After overdischarging the battery does not preserve its performance
properties. In the worst-case scenario, the battery is damaged and cannot store energy any longer.

Note

that if you do not use your Nordic ID Morphic for a long time, remove the battery from its

battery chamber. Never store the battery in the device.

Note

that the battery may not be flat nor be fully charged for long-time storage. The ideal charge is

about 60% of the battery’s full capacity.

Nordic ID International Headquarters

Myllyojankatu 2A
FI-24100 SALO
FINLAND

Phone:

+358 2 727 7700

Fax:

+358 2 727 7720

Email: [email protected]

www.nordicid.com

«
...
10
11
12
13
14
...
»

Содержание Morphic



























































Отзывы:

Нет отзывов

Похожие инструкции для Morphic

Бренд: Harbor Freight Tools Страницы: 36

Бренд: Newland Страницы: 114

Бренд: ACS Страницы: 13

Бренд: Conceptronic Страницы: 21

Бренд: Doorentryonline Страницы: 12

Бренд: Motorola Страницы: 422

Бренд: Motorola Страницы: 263

Бренд: Motorola Страницы: 440

Бренд: IFM Electronic Страницы: 37

Бренд: Star Micronics Страницы: 2

FlashLink UCF-100

Бренд: SimpleTech Страницы: 4

Бренд: HikRobot Страницы: 111

Бренд: RocketFish Страницы: 2

ABS/EBS B-DH A101

Бренд: WABCO Страницы: 292

Бренд: RIOTEC Страницы: 3

Бренд: RIOTEC Страницы: 4

SafeQ Ethernet Reader

Бренд: Ysoft Страницы: 17

Бренд: Datalogic Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды