Nimbra 300 Series Скачать руководство пользователя страница 83

Страница: 83 / 83

Installation and Maintenance Manual Nimbra 300 Series

Specifications

•

SFPs for OC-48/STM-16 ports

There are 4 different types of single wavelength OC-48/STM-16 SFPs with
different ranges.

Product number

SONET/SDH
Interface type

Wavelength

Fiber type

Range

NPA0022-LS11

SR-1/I-16

1310nm

Singlemode

2 km

NPA0022-LJ11

IR-1/S-16.1

1310nm

Singlemode

15 km

NPA0022-LL11

LR-1/L-16.1

1310nm

Singlemode

40 km

NPA0022-VL21

LR-2/L-16.2

1550nm

Singlemode

80 km

Multirate CWDM SFPs

There are 8 different wavelength variants of the CWDM multirate SFP.
This module can be used for any of the ports mentioned above but is most
commonly used as OC-48/STM-16 or OC-12/STM-4 trunk interface.

Product number

Interface type

Wavelength

Fiber type

Range

NPA0023-1470

LR-2 CWDM

1470 nm

Singlemode

80 km

NPA0023-1490

LR-2 CWDM

1490 nm

Singlmode

80 km

NPA0023-1510

LR-2 CWDM

1510 nm

Singlemode

80 km

NPA0023-1530

LR-2 CWDM

1530 nm

Singlemode

80 km

NPA0023-1550

LR-2 CWDM

1550 nm

Singlemode

80 km

NPA0023-1570

LR-2 CWDM

1570 nm

Singlemode

80 km

NPA0023-1590

LR-2 CWDM

1590 nm

Singlemode

80 km

NPA0023-1610

LR-2 CWDM

1610 nm

Singlemode

80 km

Note 1: CWDM SFPs with extended reach are available on request.
Note 2: DWDM SFPs compatible with the ITU-T 100GHz grid are available on
request.

Regulatory Compliance Information

All modules

FCC part 15 Class A

EMC Directive 89/336/EEC: ETSI EN 300 386-2 V1.1.3/ETSI EN 300 386 V1.3.1

Environmental: ETSI EN 300 019 Class 3.1E - Operational

UL1950/EN60950/UL60950-1/EN60950-1

Содержание 300 Series




















































































Результаты поиска

Содержание 300 Series

Отзывы:

Бренды по названию

Популярные бренды

Nimbra 300 Series, Руководство по установке и обслуживанию

Результаты поиска

Содержание 300 Series

Отзывы:

Бренды по названию

Популярные бренды