Nimbra 300 Series Скачать руководство пользователя страница 82

Страница: 82 / 83

•

Contents

Installation and Maintenance Manual Nimbra 300 Series

SFP Transceivers

SFP modules are currently used on the following access and trunk boards in the
Nimbra One of multi service switches:

•

OC-3/STM-1 Access Module

•

Gigabit Ethernet Access Module

•

4 x OC-3/STM-1 Trunk Module

•

OC-12/STM-4 Trunk Module

•

2 x OC-12/STM-4 Trunk Module

•

OC-48/STM-16 X-ADM Module

SFPs for OC-3/STM-1 ports

There are 4 different types of single wavelength OC-3/STM-1 SFPs with different
ranges.

Product number

SONET/SDH
Interface type

Wavelength

Fiber type

Range

NPA0016-LS11

Not Applicable

1310nm

Multimode

2km

NPA0016-LJ11

IR-1/S-1.1

1310nm

Singlemode

15km

NPA0016-LL11

LR-1/L-1.1

1310nm

Singlemode

40km

NPA0016-VL21

LR-2 /L-1.2

1550nm

Singlemode

80km

Note: SFP with electrical interface is available on request.

SFPs for OC-12/STM-4 ports

There are 3 different types of single wavelength OC-12/STM-4 SFPs with different
ranges.

Product number

SONET/SDH
Interface type

Wavelength

Fiber type

Range

NPA0014-LJ11

IR-1/S-4.1

1310nm

Singlemode

15 km

NPA0014-LL11

LR-1/L-4.1

1310nm

Singlemode

40 km

NPA0014-VL21

LR-2/L-4.2

1550nm

Singlemode

80 km

SFPs for Gigabit Ethernet ports

There are 3 different types of single wavelength Gigabit Ethernet SFPs with
different ranges.

Product number

Interface type

Wavelength

Fiber type

Range

NPA0012-S011

850nm

Multimode

500m

NPA0012-L101

1310nm

Singlemode

10km

NPA0012-V701

1550nm

Singlemode

70km

Note: SFP with electrical interface 1000Base-T is available on request.

Содержание 300 Series




















































































Результаты поиска

Содержание 300 Series

Отзывы:

Бренды по названию

Популярные бренды

Nimbra 300 Series, Руководство по установке и обслуживанию

Результаты поиска

Содержание 300 Series

Отзывы:

Бренды по названию

Популярные бренды