manualshive.com logo in svg

Nimbra 300 Series, Руководство по установке и обслуживанию

Поделиться
Скачать
Nimbra 300 Series Скачать руководство пользователя страница 13

Installation and Maintenance Manual Nimbra 300 Series

Product Overview  

•

  11

©2006 Net Insight AB, All rights reserved

inputs and the output are galvanically isolated.
Note! Alarm functionality is not yet implemented.

The front panel provides the following fixed interfaces for Nimbra 340:

•

 

Two ASI channels (A and B) for transport of video streams, each utilising
three 75 Ohm, BNC connectors for transmit, receiving and monitoring
purposes. In and Out connectors are accompanied with dedicated red/green
LED indicators, which reflect activity and status on the corresponding link.
MON (monitor) connector is accompanied with a push button and two green
LED indicators. The pushbutton allows to select whether the In or Out
stream should be routed to the monitor output, while the LED indicators
show the selection.

The front panel provides the following fixed interfaces for Nimbra 340-HD:

•

 

One HD-SDI channel for transport of video streams, utilising 75 Ohm BNC
connectors for transmit, receiving and monitoring purposes. In and Out
connectors are accompanied with dedicated red/green LED indicators,
which reflect activity and status on the corresponding link.

The front panel provides the following fixed interfaces for Nimbra 360:

•

 

Two Time Synchronization Interfaces (TSI) with 50 Ohm BNC physical
connectors

•

 

Trunk interfaces – delivered by default without SFPs, can be equipped with
OC-3/STM-1, OC-12/STM-4 or OC-48/STM-16 optical SFPs.

In the table below, a summary of which interfaces are available on which
Nimbra 300 series switches.

Interface/LED

Nimbra 340

Nimbra 340-HD

Nimbra 360

Power A and B

x

x

x

Gigabit Ethernet

x (SFP needed)

x (SFP needed)

x (SFP needed)

Reset pushbutton
Status LED

x

x

x

Serial control
interface, RJ-45

x (RS-232)

x (RS-232)

x (RS-232)

Ethernet control
interface, RJ-45

x

x

x

SYNC_IN

x (75 Ohm, BNC)

x (75 Ohm, BNC)

SYNC_OUT

x (75 Ohm, BNC)

x (75 Ohm, BNC)

Alarm (6 in, 1 out)

x

x

ASI (2 out, 2 in, 2
monitor)

x (75 Ohm, BNC)

HD-SDI

x (75 Ohm, BNC)

TSI (2 interfaces)

x (50 Ohm, BNC)

Trunk

4 x OC-3/STM-1

4 x OC-12/STM-4

2 x OC-48/STM-16

optional

Table 1 . Summary of interfaces on Nimbra 300 series switches

Содержание 300 Series




















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды