manualshive.com logo in svg

Nimbra 300 Series, Руководство по установке и обслуживанию

Поделиться
Скачать
Nimbra 300 Series Скачать руководство пользователя страница 3

Installation and Maintenance Manual Nimbra 300 Series

Contents  

•

  i

©2006 Net Insight AB, All rights reserved

Contents

About This Manual

5

Overview..............................................................................................................................5
Intended Reader ...................................................................................................................5
Support and Assistance ........................................................................................................5
Organization of Content.......................................................................................................5
Conventions in This Manual................................................................................................6

Information of Specific Importance.......................................................................6
Instructions ............................................................................................................6
Terminal Output and Keyboard Input....................................................................6

Product Overview

7

General.................................................................................................................................7
Hardware Overview, Nimbra 300 Series .............................................................................9
Trunk Modules...................................................................................................................13

OC-48/STM-16 X-ADM Trunk Module .............................................................14
4 x OC-3/STM-1 Trunk Module .........................................................................15
OC-12/STM-4 Trunk Module .............................................................................16
2 x OC-12/STM-4 Trunk Module........................................................................17
4 x DS3/E3 Trunk Module ..................................................................................18
1 Gbps Optical Trunk Module, SH and LH.........................................................19

Access Modules .................................................................................................................21

E1 Access Modules .............................................................................................22
T1 Access Module...............................................................................................22
Fast Ethernet Access Module ..............................................................................23
Gigabit Ethernet Access Module .........................................................................24
4 x OC-3/STM-1 Access Module ........................................................................25
SDI Video Access Module ..................................................................................26
ASI Transport Access Module (6 ports)..............................................................27
8 x ASI Transport Access Module.......................................................................28
8 x AES/EBU Access Module.............................................................................29

Transceiver Modules..........................................................................................................30

Introduction .........................................................................................................30
SFPs for OC-3/STM-1 ports................................................................................30
SFPs for OC-12/STM-4 ports..............................................................................31
SFPs for Gigabit Ethernet ports...........................................................................31
SFPs for OC-48/STM-16 ports............................................................................31
Multirate CWDM SFPs .......................................................................................31

Installation

33

Unpacking and Inspection .................................................................................................33
Installation Requirements ..................................................................................................33

Mechanical Requirements ...................................................................................33
Environmental Requirements ..............................................................................33
Air-flow ...............................................................................................................34
Power Requirements............................................................................................34
Ferrite clamp........................................................................................................35

Grounding Procedures .......................................................................................................36

Содержание 300 Series




















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды